Doozer-CNC-Machine

Error creating thumbnail: Unable to save thumbnail to destination

Yellow Tag Tool

Contact Owner Before Using

Tool Owner: Karen Englebeck

Chat: @zebragrrl on on Slack

Email: See sticker on machine.

test

---

🚨 This is an ongoing project, tool is not functional yet 🚨

Project Objectives

The following is the list of design goals and hoped-for features. Core Objectives Build a CNC machine capable of milling acrylic or pressboard - the standard backing board of the ubiquitous inexpensive clipboard. Build the machine using mostly salvaged and found parts. Machine should operate using a standard Arduino Uno board, with the standard CNC expansion board kit. Workflow should be possible from Error creating thumbnail: Unable to save thumbnail to destination Inventables Easel to Error creating thumbnail: Unable to save thumbnail to destination Universal Gcode Sender. Purchased parts should ideally be the cheapest available. Machine should have interchangeable tool functionality, so the gantry can be used to utilize a number of different tools. Those tools potentially could include: Error creating thumbnail: Unable to save thumbnail to destination Dremel Carver (or inexpensive WEN alternative) - possibly mounting the tool-end of the Flexible-Shaft attachment, to reduce machine vibration. Error creating thumbnail: Unable to save thumbnail to destination Embroidery Hoop on extension arm, allowing a minimally modified sewing machine to create embroidered patches. May be better as a secondary machine. Error creating thumbnail: Unable to save thumbnail to destination Free-Rotating 'Drag Knife' or inexpensive Error creating thumbnail: Unable to save thumbnail to destination Vinyl Cutter replacement blade cartridges. Error creating thumbnail: Unable to save thumbnail to destination Filament Extruder and Hot-End for 3D printing, or Error creating thumbnail: Unable to save thumbnail to destination modified 3D Pen May require secondary Arduino pre-configured as 3D printer instead of CNC. Possibly could use a serial port switchbox to switch arduinos, usb, etc?? Error creating thumbnail: Unable to save thumbnail to destination Inexpensive soldering iron with copper wire to replace tip, for cutting foam. Error creating thumbnail: Unable to save thumbnail to destination Reciprocating needle cutter for cutting cardboard or foam-core. Error creating thumbnail: Unable to save thumbnail to destination Pen or Pencil holder for use as plotter. Error creating thumbnail: Unable to save thumbnail to destination Uses Part 1 Error creating thumbnail: Unable to save thumbnail to destination Uses Part 2 Error creating thumbnail: Unable to save thumbnail to destination Uses Part 3 Fabric markers for making t-shirts/wall hangings, paint markers or metallic sharpies for marking surfaces like glass, mirrors, tile, and chalkboards. Error creating thumbnail: Unable to save thumbnail to destination Glue pen for heat embossing Error creating thumbnail: Unable to save thumbnail to destination Ball-point pen without ink, for use as pressure embosser/creasing tool. Error creating thumbnail: Unable to save thumbnail to destination Cutting Laser - at a later date, as funding permits Secondary Objectives Clamping area should be able to accommodate a standard 9" x 12.5" clipboard, with the clip removed, whether or not it can mill that entire area. Tertiary Objectives The footprint of the completed machine should not exceed 12.5" x 16.5" (to fit inside folding cart for easy transport) Creeping Featuritis - Acquired Objectives It's nearly inevitable when any suitably complicated project drags on, or even goes on hiatus. Eventually you're going to start daydreaming new ideas and features for the build. The Doozer was no exception to this. The trick is to try to make sure that the feature creep is actually a reasonable addition that can be missed out if need be, due to budget or skill constraints. The following is a lits of ideas that cropped up along the way, that made the cut. Redesign machine to use aluminum extrusion for the major structural elements Upgrade to using actual lead screws and aluminum shaft-to-motor couplers from the start - not 'later date' upgrades All parts created components should be either copies of purchaseable replacements, or be capable of being made WITH the machine. Slotted waste-board that allows carriage bolts to travel in the aluminum extrusion below, for clamping materials down with wingnuts. Waste board slats should also be possible to make/replace WITH the machine! Laser Crosshair built into the X Axis to allow for 'same every time' axis zeroing, and thus repeatable jobs. Error creating thumbnail: Unable to save thumbnail to destination USB 10-key number-pad for use as a Error creating thumbnail: Unable to save thumbnail to destination remote positioning/control pendant for the CNC.

Project Status

01/16/2020 - Latest!

After days of near constant slaving away at the 3d modelling software, I now have a blueprint going forward. l also have some parts counts that I can look at... and it's not an entirely pretty picture. 50 custom mounting brackets. Thankfully many of them are reused 2, 4, even 10 times, so there's only 18 unique bracket shapes. 348 metric screws, which breaks down to over 250 M5s in 4 lengths, and nearly 100 M3s in 3 lengths. I placed a parts order on AliExpress for the screws and a spare Arduino CNC kit... just in case I earn the Level II Blue Smoke Metric Badge.

The next phase in this project, aside from waiting over a month for overpriced machine screws from China (and trust me, they were the cheapest I could find!) is to begin cutting out the brackets. Original plans were to 3D print a set of them first for putting the machine together for proving.. and honestly, that's still an option for a lot of them. I may start putting some of the odd-colored filaments at my house to work on the smaller, large quantity brackets. Other brackets I will either use the big CNC table at the shop to mill out of 'plex' (whatever scrap acrylic, plexiglas, or whatever I can find), or to ideally make use of a laser cutter.

Once the proving set of brackets is done, I can see if adjustments need to be made. I'll also be able to start trying to bring the machine to life.

Known elements still to be done:

• Tool Mounting Plate

  I have located a couple of aluminum chunks that may be able to be milled into a permanent mounting block for tools. This has been set aside for future use.

• Work Surface

  This will be made out of 2525 aluminum extrusion.. and while I have a fair amount, I don't have huge quantities. The final design of how this will work is still on-hold, pending some more practical forward progress. There is a possible future where this extrusion ideal is abandoned, and replaced with a couple sheets of MDF and some standard SAE threaded plywood anchors.

• Deflector Shields

  Simple angled plates for keeping sawdust from fouling the Y axis screws. Mountings for these will be designed once the Work Surface is sorted out.

Project Development History

⬇ Click here to expand section ⬇

01/16/2020

After days of near constant slaving away at the 3d modelling software, I now have a blueprint going forward. l also have some parts counts that I can look at... and it's not an entirely pretty picture. 50 custom mounting brackets. Thankfully many of them are reused 2, 4, even 10 times, so there's only 18 unique bracket shapes. 348 metric screws, which breaks down to over 250 M5s in 4 lengths, and nearly 100 M3s in 3 lengths. I placed a parts order on AliExpress for the screws and a spare Arduino CNC kit... just in case I earn the Level II Blue Smoke Metric Badge.

The next phase in this project, aside from waiting over a month for overpriced machine screws from China (and trust me, they were the cheapest I could find!) is to begin cutting out the brackets. Original plans were to 3D print a set of them first for putting the machine together for proving.. and honestly, that's still an option for a lot of them. I may start putting some of the odd-colored filaments at my house to work on the smaller, large quantity brackets. Other brackets I will either use the big CNC table at the shop to mill out of 'plex' (whatever scrap acrylic, plexiglas, or whatever I can find), or to ideally make use of a laser cutter.

Once the proving set of brackets is done, I can see if adjustments need to be made. I'll also be able to start trying to bring the machine to life.

Known elements still to be done:

• Tool Mounting Plate

  I have located a couple of aluminum chunks that may be able to be milled into a permanent mounting block for tools. This has been set aside for future use.

• Work Surface

  This will be made out of 2525 aluminum extrusion.. and while I have a fair amount, I don't have huge quantities. The final design of how this will work is still on-hold, pending some more practical forward progress. There is a possible future where this extrusion ideal is abandoned, and replaced with a couple sheets of MDF and some standard SAE threaded plywood anchors.

• Deflector Shields

  Simple angled plates for keeping sawdust from fouling the Y axis screws. Mountings for these will be designed once the Work Surface is sorted out.

1/5/2020

Progress in SketchUp is going really well. The bracket designs are starting to take shape. I'm assuming that they'll be made of 1/8" thick (~3mm) aluminum plate. Overall I'm fairly pleased with the project as it's coming along, though in watching other people's projects on YouTube, I certainly do have my doubts. Each of the 3 axis is basically resting on four linear bearings, each held in place with four m3 screws. I've done my best to make their stance as square as possible for maximum rigidity, but I still have my concerns.

At the end of the day, it's all going to be made of metal, mostly aluminum extrusion with steel rods. While the machine will hopefully be capable of occasional milling of aluminum, the 'router' will still be a Dremel. The Doozer's more common use will be for milling materials that are much less resistant: Acrylic, ABS/PVC/Polystyrene Sheet, MDF, Pressboard, Veneer, and Balsa Wood.

01/03/2020

I had the opportunity to speak with Keith Legg on New Years Eve, in regards to machining some of the needed custom brackets for the linear rod , motor, and threaded rod bearing mounts. That part of the equation is a resounding GO.

This evening I re-inventoried my box of previously acquired components.. motors, rods, screws, and so on.. and I’m looking forward to returning to the design process with renewed enthusiasm. Looking forward to beginning finalizing the design, so I can finally begin BUILDING.

Soon, I hope!

09/20/2019

Email received from AliExpress. All components of the targeting laser assembly ( crosshair & dot lasers and USB power adapter ) are now in the hands of couriers in the USA.

Beata donated a 2-port USB power converter to the project after I'd ordered the single-USB version, so I may utilize the dual-port unit instead (one for each laser)

09/18/2019

All off-the-shelf structural components have been purchased, and have arrived. All components are measured and 3D modelled in SketchUp Make 2016. The 3 axis assemblies have been assembled in SketchUp.

Currently developing a modified 3D model of the tolerances of the aluminum extrusions, that model will help me easily create functional 3D-printed parts that fit properly.

Maximum workspace dimensions seem to be coming in at (305mm x 250mm x 180mm), which is approximately (12in x 11in x 7in). These are the maximum lengths that the linear rails and bearings can accommodate. I suspect these lengths will reduce somewhat as the actual gantry is designed.

---

What even is a ‛Doozer’?

⬇ Click here to expand section ⬇

Funko Pop Doozer

Fraggles and Doozers

The Doozers are a race of characters from Jim Henson's Fraggle Rock television series. Doozers love to work all day long. They're tiny, green creatures who usually sport construction helmets, boots, and tool belts. Doozers stand approximately knee-high to Fraggles, at six inches tall.

When compared to the other races within Fraggle Rock, they are by far the most technologically advanced. Most Doozers are construction workers, while others are architects or miners. With the help of various Doozer machines and vehicles, they build elaborate constructions all over Fraggle Rock, like towers, buildings, roads and bridges. Doozer constructions are the Fraggles' favorite snack, and they love to eat the buildings that the Doozers build. The Doozers don't mind their buildings being eaten -- if the Fraggles didn't eat the constructions, the Doozers would run out of building space!

---