Various 3D Printer Projects
New3d Printers /
Jump to navigation
Jump to search
We've had the opportunity to put together some 3D printers. Here are some notes on that
.
Aluminatus Trinity One Printers:
These are big mostly 80/20 (40-4030?) channel aluminum beasts.
Parts List:
| Number | Name | Description |
| 1 | Base | All electronics, 2 Power supplies, Controler, 3 Motors, etc... |
| 1 | Display / Control Board | Allows independent control of printer, W/ Ribbon cables |
| 2? | Plastic mounting parts | For above |
| 1 | Top Plate | With holes and slots |
| 24 | M5x10 Screws | Button Head Cap Screws, for above |
| 8 | M5 T-Slot Nuts | For slots in short sides of base, for above |
| 1 | Power inlet with Switch | For above |
| 8 | Triangle Blocks | For vertical 80/20 frame |
| 16 | M5x10 Screws | Socket Head Cap Screws |
| 16 | M5 T-Slot Nuts | For above |
| 2 | Triangular Plates | To attach vertical 80/20 |
| 10 | M5x10 Screws | Socket Head Cap Screws, to attach above |
| 10 | M5 T-Slot Nuts | For above |
| 3 | 80/20 Slotted x 21" | Posts to hold Gantry |
| 2 | Lead Screws 15.75" | With Nuts and Torsion dampeners |
| 8 | Set Screws | For above |
| 1 | Lead Screw 16.5" | for Gantry |
| 1 | 80/20 Slotted x 16.75"" | To mount the above on |
| 2 | Vertical Slide Rods | For Gantry 21.5" long |
| 2 | Thin cork disks | For above |
| 4 | Plastic Clamp Ends | For above |
| 8 | M5-10 Screws | Cap Screws, for above |
| 4 | M3-14 Screws | CS, For above |
| 4 | M3 Nylocks | For above |
| 2 | Plastic Bushing Holders | To mount Gantry to Vertical Slide Rods |
| 8 | M5-10 Screws | CS For above |
| 2 | Plastic Spacers | For abvoe |
| 1 | Bed | Frame for build bed |
| 2 | Spacer Blocks | To hold bed above top plate |
| 4? | M6 Screws | For above |
| 4 | Plastic Bed Corners | To hold glass on bed |
| 1 | Hot End | |
| 1 | Plastic HE Mount | For above |
| 1 | Metal retaining plate | For Hot End |
| 2 | M5-16 CS | and nuts for above |
| 1 | Extruder Motor | 36JX30K5.18G or 36JX30K27G |
| 1 | Pinch Bearing | For above + Short Shaft |
| 1 | Hobbed Drive wheel | For above |
Notes:
- When printing parts try to include T-slot nut cage forks so they don't slide away when you remove the screw. Perhaps with small barbs so they are pulled tight.
- If any steppers are skipping steps you might want to adjust the Pololu driver board's current limit. As described in the links below.
- CS for bottom plastic plates, are M5-7.
- Other part numbers for Extruder motors are:
- 36JX30K5.18G/42STH38-1684A, 1.8 Degree, 2.8V, 1.68A 1:5.18 Gear Ratio
- 36JX30K27G..., 1:27 Gear Ratio
- 36JX30K100G..., 1:100 Gear Ratio
- Hot End Cooling fan: AV-F4010LS
- 24V 0.08A 4-6? CFM
URLS:
- http://reprap.org/wiki/Aluminatus_TrinityOne_Software_Electronics
- http://reprap.org/wiki/Pololu_stepper_driver_board
- http://www.discountsteel.com/items/5052_Aluminum_Plate.cfm?item_id=125&size_no=1
- 5 mm aluminum sheet
- I think it's 3/16 though
Adjusting the Vertical Slide rods:
- Mount clamps in the base with locktight, but leave M3 screws lose.
- Slide plastic gantry mounts with bushings on the slide rods
- Thread the lead screws in also, add retainers and holding screws.
- Add Claps to top of rods
- Slide T-Slot nuts into top piece for the clamps.
- Loosely mount motors
- Slide rods into base clamps and connect motors to torsion dampeners.
- Loosely fasten in upper clamps.
- Tighten all four M3 bolts on clamps
- Measure distance to 80/20 at bottom of slide rods.
- Tighten top clamp screws without locktight enough so you can still move the clamps a bit
- Adjust top of rods to same distance and tighten one clamp screw till its firm.
- Add locktight to the other one and re-thread and tighten.
- Remeasure to double check distance.
- Add locktight to the first one check distance and tighten
- Repeat for the other rod.
Adjusting the lead screws and motor mountings:
Random Notes:
- Some Stepper driver board: 6B6560-3V5
-- Main.ClifCox - 25 Apr 2016